Modern Classic SLRs Series :
Olympus Winder 1 - Instruction Manual - Part 2

 

HTML Page (32k) Loading ...

OM Power WINDER 1 Operation Manual

Coin.jpg
1. Remove the motor drive socket cap from the camera base plate by rotating it counterclockwise with a coin until the index dot of the cap is aligned with the index dot of the camera. * Store the socket cap in the Winder 1 to avoid loss because it will be very troublesome to locate one later.

Pull.jpg Turn.jpg
2. Pull up and rotate the Switch Dial to the "OFF" position. Release the dial making sure that the dial is securely in place and does not move. 3. Insert the Guide Pin into the guide pin hole on the camera base plate, and the Clamping Screw into the tripod socket.

Mount1.jpg Mount2.jpg
To assure proper connection, adjust the 'position of the Winder 1 until it is flush with the camera.

4. Turn the Clamping Screw clockwise until the Winder 1 is securely attached to the camera base plate.

Slide.jpg Slot.jpg
* The Socket Cap Storage is positioned at the underside of the entrance of the Battery Holder Compartment.

1. Slide the Battery Holder Lock Button on the bottom of the Winder 1 in the direction of the arrow: the Battery Holder will spring out of the compartment slightly for easy removal. Pull out the Battery Holder. 2. Insert and push horizontally the removed motor drive socket cap into the Socket Cap Storage with its claws facing up.

Detach.jpg Twist.jpg
1. To detach the Winder 1, turn the Clamping Screw counter-clockwise. 2. Retrieve the motor drive socket cap from the Socket Cap Storage.

3. To replace the cap on the camera base plate: Align the index dot on the cap with the index dot on the camera, press and turn the cap clockwise with your finger to engage the thread. Then continue turning with a coin until the groove on the cap is aligned with the index dot on the camera.

Cells.jpg Slotin.jpg
1. Pull out the Battery Holder. 2. Insert four 1.5V AA (Penlight) size batteries into the Battery Holder as indicated by the polarity marks, pushing against the spring.

* If the batteries are inserted upside down, the motor will not function. (The polarity protection mechanism interrupts current flow.)

3. Insert the Battery Holder back into the compartment until it snaps into place. The Battery Holder Lock Button will automatically reset itself to the lock position.

Cells.jpg
4. Three types of batteries are available on the market - Manganese, Alkaline and Ni-Cd rechargeable batteries. The numbers of 36 exposure film that can be taken with a set of fresh batteries are: Manganese - approx. 20 rolls; Alkaline - approx. 50 rolls; Ni-Cd - approx. 15 rolls

Turn.jpg Focus.jpg
1. Pull up and rotate the Switch Dial to the "SINGLE" position. Release the dial, making sure that it is securely in place and does not move. * The Switch Dial can be locked in two places other than "SINGLE" and "OFF". In actual use, set the dial to the indexed positions only.

2. Press the Shutter Release to take pictures. * Before loading the camera with film, run several blank shots by pressing the Shutter Release to make sure the units are attached properly. ** Should you wish, you can manually transport the film advance lever and press the camera's shutter release even with the Winder 1 attached. The film can then be advanced manually or with the motor for the next shot.

FilmStrip.jpg
1. Always try to load your camera after the Winder 1 has been attached. This eliminates even the remotest possibility of light leak through the motor drive socket. If this is not possible, attach the Winder 1 in a dimly-lit area. 2. Load the camera with film in the normal manner.

RewindCrank.jpg
1. Always try to load your camera after the Winder 1 has been attached. This eliminates even the remotest possibility of light leak through the motor drive socket. If this is not possible, attach the Winder 1 in a dimly-lit area. 2. Load the camera with film in the normal manner. 3. Unload the film in the normal manner.

Helpful Hints

* If Winder Stop Functioning .... 1 ) Check the exposure counter. The Winder 1 automatically stops advancing after the last frame is exposed. Rewind the film into the cartridge. Important: After the last frame is exposed, avoid pressing the Shutter Release to prevent the possibility of film damage. 2) if the Winder 1 stops in the middle of a roll and makes a droning sound, the batteries are exhausted. Turn the Switch Dial to "OFF" and insert fresh batteries.

* Shooting in Low Temperature/Cold Climate Areas 1 ) if the Winder 1 will not advance ~when shooting in extremely cold temperatures, advance the first frame manually and then use the motor. 2) if the Winder 1 will still not function, the batteries are exhausted or the temperature is too low; replace the batteries with fresh ones or warm the units OR use the relay cord with external power.

250Film.jpg Film250.jpg
* Using OM System 250 Film Back 1 with Power Winder 1 The OM System 250 Film Back 1 provides up to 250 exposures on 10m (30 ft.) lengths of bulk load film. The outline of its operating procedures is described in the followings. 1) Shift the Gear Cover on the 250 Film Back Coupling Gear to reveal the gears. 2) Replace the standard camera back with the 250 Film Back 1. The Film Back can conveniently be attached to the camera before or after the Winder 1. 3) Set the subtractive-type exposure counter manually.

250FilmBack.jpg
4) The 30m (100 ft.) film is taken out of its storage can, rolled round the supply spool, cut at the desired lengths and put in the 250 Film Magazine, which along with the take-up magazine, is installed into the 250 Film Back 1. (For details see Operating Instructions for 250 Film Back 1.) * The 250 Film Loader is available to make film spooling from the 30m film fast and easy.

Remote.gif
4) The 30m (100 ft.) film is taken out of its storage can, rolled round the supply spool, cut at the desired lengths and put in the 250 Film Magazine, which along with the take-up magazine, is installed into the 250 Film Back 1. (For details see Operating Instructions for 250 Film Back 1.)

Remote Control Jack on top of the hand grip of the Winder 1 provides a facility for electric shutter release in simultaneous bursts with two or more motorized OM cameras. The wiring is illustrated above. * Prior to the wiring, set the Switch Dial to "OFF"; if set to "SINGLE", the Winder 1 may start functioning as soon as the connection is made.

Remote2.gif
1. The Remote Control Jack provides a facility for remote motor drive photography. The jack accepts a 2.5mm mini plug (output terminal of remote control apparatus).

* When inserting the mini-plug into the jack, the Switch Dial should be set to "OFF"; otherwise the Winder 1 may start functioning as soon as the connection is made. 2. Commercially available remote control apparatus, such as radio- or photo control devices, self timers, intervalometers and remote control cords are applicable.

External
Power Source:

ExternalSource.jpg Cord.jpg
1. The External Power Jack at the center of the Switch Dial accepts the power plug from an external power unit of up to DC 6V (4 - 5.5V with a power unit of large potentiality). 2. Connect the power plug with the jack referring to the illustration above.

Note: Extremely low temperatures may cause the battery power to drop and the Winder 1 may fail to function normally. To prevent voltage drop, tuck the external power unit in your pocket and connect it with the Winder 1 via the remote cord. * Ni-Cd batteries may supply enough power even at around 0°C. (At purchase of Ni-Cd batteries, it is recommended to get four pieces of them packaged as a set.). External Power Pack such as M.6V Power Pack 1 or 2 is also recommended. * M.6V Power Pack 1 holds 4 AA batteries, while the M.6V Power Pack 2 holds 4 D batteries.

* Make sure the Winder 1 is attached to the camera securely. Do not apply excessive force.
* Do not apply force when the movable parts have been stopped by the safety mechanism.
* After shooting with the Winder 1, always turn the Switch Dial to "OFF".
* Keep all electrical contacts clean and well away from metallic objects to prevent short circuit.
* At sub-zero temperatures, the batteries may sometimes fail to function normally. Warm them up before use.
* Do not hit or drop the Winder 1, or let it strike any hard object.
* When storing the Winder 1 for long periods, remove the batteries from the Battery Holder for longer battery life.
* Avoid storing the Winder 1 in very cold, hot or humid areas.
* Do not store the units near mothballs or similar materials to avoid the possibility of damage to metal surfaces.
* If cleaning is necessary, wipe the units with a soft cloth only. Do not use cleaning solvents or other harsh chemicals.

| Previous | Back to Index Page of Winder 1

| Back | to Index Page of Motor Drives and Winders

| Back | to Index Page of OM1(n)
| Back | to Index Page of OM2(n)
| Back | to Main Index Page of OM1(n) & OM2(n)

Olympus OM-1(n): Main Index Page (5 Parts) | Camera Operations (6 Parts)
Specifications:
HTML | PDF | Main Reference Map: HTML | PDF (217k)
Olympus OM-2(n): Main Index Page (6 Parts) | Camera Operations (9 Parts)
Specifications:
HTML | PDF (48k) Main Reference Map: HTML | PDF (203k)
Olympus OM-2SP: Camera Operations | Other Issues
Specifications: HTML | PDF | Main Reference Map: HTML | PDF

Shared Resources: Supplementary articles: TTL Metering, Depth of Field, Shutter Speed & Aperture
Motor Drive and Power Winder: Main Index Page (4 Parts)
Motor Drive 1 | Motor Drive 2 | Winder 1 | Winder 2
Flash Photography:
Main Index Page (4 Parts)
T45 | T32 | T20 | F280 | S20 | Qucik AUTO 310 | QA300, 200, 200S
Macro-Photography:
Main Index Page (3 Parts)
Macro Flash Units:
T10 Ring Flash, T28 Twin, T28 Single, T8 Ring Flash
Accessories:
Databack 1-4 | Screens | Finder Accessory | Remote | Cases

Zuiko Lenses: Slowly developing..

Glossary of Photography
A good external source for
used Instruction Manuals for various OM SLRs and Accessories.

| Message Board | for your favourite Olympus OM-1(n) and OM-2(n) series models
| Message Board | for your Zuiko Optics in a shared environment
| Message Board | Specifically for Dispose or Looking for OM Photographic Equipment

About this photographic site.

MIR Logo
Home - Photography in Malaysia
Search.gif

Copyright © 2000. leofoo ®. MIR Web Development Team.

Site & Message Board Maintainers: Mr. Simon Evans <sje@lrc.ruralwales.org>; Mr. Rick Oleson <rick_oleson@yahoo.com>; Mark Dapoz <md@dementia.org>

Credit: My old time buddy, Ahmad Ikram, Dr of Rubber Research Institute (RRI), Malaysia who shares the same passion with me and also lending his OM-1n, OM-4 and the Motor Drive 1 to me for preparing some images in this site; Mark Dapoz <md@dementia.org>for reminding some broken links; Mr Poon of Foto Poon, Ipoh, Mr Richard, Ampang Park, Mr Lim and Miss Jenny of Foto Edar for their generosity for their OM1(n), OM2n camera and some Zuiko lenses. Mr Hans van Veluwen for mistakenly using some content earlier from his OM website; J Sorensen for providing some useful images to rectify some technical "flaws"; Mr Gen Holst for helping during the early stages of development of this OM site; Mr KKLow for some of his earlier images on the OM-1appeared in this website; Miss Wati and Mirza for helping me to convert this Operation Manual into a HTML format. Mr MCLau for rectifying some mistakes made on the earlier preview sites. Site created 'unfortunately' again with a PowerMac. A personal tribute to the creator of the OM system and also a site dedicated to all the fans of Olympuses and Zuiko Optics worldwide. Some of the content and images appeared in this site were scanned from OM official marketing leaflets, brochures and instruction manual(s) for educational purposes. Olympus is a registered tradename of Olympus Optical Inc., Japan.